Courtesy Lights stay on?
#1
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2009
Location: Newfoundland, Canada
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
Courtesy Lights stay on?
after I got everything swapped from the 96 ssei to my 93 se, the courtesy lights stay on, its not the door switches because they all work and when I turn the key back with the doors closed it still retains its power tell i open any door, and also the door open lights in the dash all work and so dose the trunk ajar light. I even unplug the dimmer switch and they stay on, what would cause this???
would it be because I disconnected them security switches on all the door locks, because my 93 did not have the switches on the locks only the ones in the handles? I dont think its them because i checked the ohm reading on them with the locks unlocked and they read nothing untell i lock the doors and they connect.
Also it says I have the rear window brake light blowed even thoe it works.
Thanks
-Brandon
would it be because I disconnected them security switches on all the door locks, because my 93 did not have the switches on the locks only the ones in the handles? I dont think its them because i checked the ohm reading on them with the locks unlocked and they read nothing untell i lock the doors and they connect.
Also it says I have the rear window brake light blowed even thoe it works.
Thanks
-Brandon
#2
DINOSAURUS BOOSTUS
Expert Gearhead
When you say you swapped everything over ... that'* pretty vague and I don't remember seeing a post about yoru plans. Please elaborate as to which BCM/MALL you are using and what "everything entails.
Thanks
Thanks
#3
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2009
Location: Newfoundland, Canada
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
i took everything from the 96 and put in the 93 i mean everything but the shell, the suspension and body flaring. I converted my series 1 se to a series 2 ssei supercharged, and swapped over the leather interior.
-wiring
-hole interior
-engine
-tranny
-air ride
-abs\traction control
-trunk lid
-wiring
-hole interior
-engine
-tranny
-air ride
-abs\traction control
-trunk lid
#6
Guest
Posts: n/a
it could be the 15a Chime fuse on the driver side fuse box.
when i had low brake fluid the e-brake thing stayed on and so did the stupid ding so i didnt know how to fix it at the time (add brake fluid..) so i just unplugged the chime fuse and noticed my lights stayed on as well, for a longer period of time though
hope this helps
when i had low brake fluid the e-brake thing stayed on and so did the stupid ding so i didnt know how to fix it at the time (add brake fluid..) so i just unplugged the chime fuse and noticed my lights stayed on as well, for a longer period of time though
hope this helps
#7
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2009
Location: Newfoundland, Canada
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
Nope not the problem, all the fuses are good, and the door chime works perfect. Thanks Anyway
-The retained acc power works perfect " shuts off when you open any door"
-The door chime works when you open the doors, and shuts off when you close them
- the lights still stay on with the dimmer switch unpluged, and when pluged in the switch for turning them on and off dose nothing they still stay on.
is there a relay that could be stuck anywhere? or anything i should look for? also why would it say my break light is out when its not?
-The retained acc power works perfect " shuts off when you open any door"
-The door chime works when you open the doors, and shuts off when you close them
- the lights still stay on with the dimmer switch unpluged, and when pluged in the switch for turning them on and off dose nothing they still stay on.
is there a relay that could be stuck anywhere? or anything i should look for? also why would it say my break light is out when its not?
#8
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2009
Location: Newfoundland, Canada
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
Ok I Performed the “MALL Module Internal Diagnostic Procedure" and i read one beep is good when in the I/O mode and no beeps are bad:
when I first get into it i get "1 beep, pause, 2 beeps, pause, 3 beeps, pause, 4 beeps, pause" this repeats a fue times before it enters I/O mode what is this???
Once i am in I/O mode i turn the dome light switch "on,i get a beep, off i get another beep, then i turn it on again the lights go out and i get a beep, then turn it off and get another beep, then they turn on the next time and this repeats"
when i open any door i get "around 5 real quick beeps then when i close it i get one beep"
Is there anything wrong here????
Thanks
when I first get into it i get "1 beep, pause, 2 beeps, pause, 3 beeps, pause, 4 beeps, pause" this repeats a fue times before it enters I/O mode what is this???
Once i am in I/O mode i turn the dome light switch "on,i get a beep, off i get another beep, then i turn it on again the lights go out and i get a beep, then turn it off and get another beep, then they turn on the next time and this repeats"
when i open any door i get "around 5 real quick beeps then when i close it i get one beep"
Is there anything wrong here????
Thanks
#9
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2009
Location: Newfoundland, Canada
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
anybody know this is driving me nuts, I unplug the fuse to get the lgihts off but the battery still runs dead after a wile, and im moving away this summer and i needs this fixed, I cant seam to figuar it out.
Anyone got a wireing diagram on the circuts that controls the lights?
Anyone got a wireing diagram on the circuts that controls the lights?
#10
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2009
Location: Newfoundland, Canada
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
Ok i found out whats wrong it is the MALL / BCM, there is a recall on the bcm in my car but i cant get a new one because i got it put in the 93 body.... dose anyone have the wireing for the bcm so i can set up the interior lights manualy, or repair the bcm.. what compaster internaily is the recall on? anyone know the ins and outs on this?
Thread
Thread Starter
Forum
Replies
Last Post