highbeams once again...please help
#1
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Dec 2003
Location: Edison, NJ
Posts: 123
Likes: 0
Received 0 Likes
on
0 Posts
highbeams once again...please help
Still having problems with my highbeams from my post here:
http://www.bonnevilleclub.com/forum/...550&highlight=
I havent really looked at the bottom of the hush panel yet, I am about to go out now, but on the column there is a plastic panel that will not stay in place, I assumed it had something to do with it. I got the drop light and took a look on the inside of the panel, I see a metal rod not connected to anything, and cannot see where it should connect, but I would assume that is the actual rod that turns the switch on and off, but where does it connect? When I play with the rod it doesnt turn on the highbeams anyway, what are the chances it is disconnected on both ends? I looked in a Chiltons manual for the bonneville and have no info on the highbeam switch, and a Haynes for a Trans Am but they have the same highbeam system, but nothing. Help me PLEASE
Here is a pic of the plastic panel I am talking about
Thanks for any help!!
http://www.bonnevilleclub.com/forum/...550&highlight=
I havent really looked at the bottom of the hush panel yet, I am about to go out now, but on the column there is a plastic panel that will not stay in place, I assumed it had something to do with it. I got the drop light and took a look on the inside of the panel, I see a metal rod not connected to anything, and cannot see where it should connect, but I would assume that is the actual rod that turns the switch on and off, but where does it connect? When I play with the rod it doesnt turn on the highbeams anyway, what are the chances it is disconnected on both ends? I looked in a Chiltons manual for the bonneville and have no info on the highbeam switch, and a Haynes for a Trans Am but they have the same highbeam system, but nothing. Help me PLEASE
Here is a pic of the plastic panel I am talking about
Thanks for any help!!
#2
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Dec 2003
Location: Edison, NJ
Posts: 123
Likes: 0
Received 0 Likes
on
0 Posts
Ok, I checked the actual switch, the rod was not connected at either ends, I reconnected it at the bottom where the rod goes into the switch, anyone know where the rod connects to on the steering column? They work, but need to finish off the column and I can go to inspection, anyone know? I have no clue where...
Thanks again
Thanks again
#3
Looking at the service manual, there is supposed to be a dimmer switch rod actuator that rests on the bend in the dimmer switch rod. Then there is a base plate that goes over that. The lever looks like it mounts on the base plate. And from there you have the housing cover and a square cap that goes on the back.
#4
Senior Member
True Car Nut
Join Date: Nov 2002
Location: Texarkana, Texas
Posts: 6,042
Likes: 0
Received 0 Likes
on
0 Posts
Is there a chance i can get a blowup of that picture? with part numbers? there'* alot of broken off parts in my column... My local dealership isn't a fun place to go....
#5
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Dec 2003
Location: Edison, NJ
Posts: 123
Likes: 0
Received 0 Likes
on
0 Posts
yeah, me too, dont really see what goes where, on the car the only cover I have is I guess the vanitycover in the pic above, then just a metal rod sticking out nothing on it just the rod. If you can scan it or even just take a picture of that picture it would help me tons. Please?
On a side note, the service manual you looked at, is that the 2 vol set by any chance? Or got the number for the book so I can order it? It sounds like that book would be very helpful in the future. THANKS !!
On a side note, the service manual you looked at, is that the 2 vol set by any chance? Or got the number for the book so I can order it? It sounds like that book would be very helpful in the future. THANKS !!
#6
Gentlemen, I don't have a scanner, otherwise I would do it for you...
Here is the factory manual link:
http://www.helminc.com/helm/product2...NUF6GWNWKG7D18
Here is the factory manual link:
http://www.helminc.com/helm/product2...NUF6GWNWKG7D18
#8
Senior Member
True Car Nut
Originally Posted by Damemorder
Is there a chance i can get a blowup of that picture? with part numbers? there'* alot of broken off parts in my column... My local dealership isn't a fun place to go....
#9
Senior Member
True Car Nut
Join Date: Nov 2002
Location: Texarkana, Texas
Posts: 6,042
Likes: 0
Received 0 Likes
on
0 Posts
There Is only one GM dealerhip in town. Pete Mankins Pontiac Cadillac Saturn (Other GM Brands Here). They are a**hats. Ithink I'll just wait for my book, buy the parts off gmpartsdirect and just b***h about how much the install sucks.
Thread
Thread Starter
Forum
Replies
Last Post