#@%$ coolant in my egr
#1
Member
Posts like a V-Tak
Thread Starter
Join Date: Oct 2009
Location: ontario canada
Posts: 74
Likes: 0
Received 0 Likes
on
0 Posts
#@%$ coolant in my egr
oh boy this is gunna hurt.
So my car starts drinking coolant like crazy, can find whats wrong oil is good , no puddle on the ground . take it to the mechanic we pressure test the system, and find coolant driping out of my egr valve.
hes saying possible cracked head or intake.
i'm saying oh god damn this is gunna be expensive
anyone shine some light on this situation and tell me its going to be ok ?
FML
So my car starts drinking coolant like crazy, can find whats wrong oil is good , no puddle on the ground . take it to the mechanic we pressure test the system, and find coolant driping out of my egr valve.
hes saying possible cracked head or intake.
i'm saying oh god damn this is gunna be expensive
anyone shine some light on this situation and tell me its going to be ok ?
FML
#2
Retired
Run back out with a flashlight, take your intake duct off, open your throttlebody and shine your light inside your Upper Intake Manifold. Check for coolant inside. Get back to us.
__________________
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
#3
Member
Posts like a V-Tak
Thread Starter
Join Date: Oct 2009
Location: ontario canada
Posts: 74
Likes: 0
Received 0 Likes
on
0 Posts
car is at the mechanics shop
coolant was in the cylinders too, car hydra-lock'd on the hoist
coolant was in the cylinders too, car hydra-lock'd on the hoist
Last edited by flaox; 01-05-2010 at 07:46 PM.
#4
Retired
I don't think I have ever heard of these engines sucking coolant through a head gasket. Not that I am saying it couldn't happen. But these UIM'* are prone to failure at the EGR inlet. Thusly sucking what you don't want it to suck. Coolant.
__________________
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
#5
Senior Member
True Car Nut
There has been issue where the UIM has cracked. regardless, you'll need to tear down the top end to see what happened. You should be able to avoid pulling the heads if it'* just UIM and or gaskets that cut loose.
#7
Senior Member
True Car Nut
#8
Retired
I agree with Kevin.
Next time you see your car, pull the dipstick and check your oil. Look for a milky substance. You don't want oil and coolant mixed together. If you find it, have the mechanic drain your entire cooling system, and change the oil.
__________________
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
#9
Senior Member
Certified GM nut
Like everyone else said, classic UIM failure. Mine went almost the same way — one horrible, misfiring one-mile drive across town, and then hydrolocked in the parking lot behind my old office.
Mechanic had to replace the plugs, wires (unrelated to the hydrolock but pretty shot), oil, coolant, and UIM. He told me that he had to dry out each cylinder by hand; the car must have been thirsty — the entire overflow tank and a good portion of the radiator were sucked dry.
If you get out of there and lose less than $800, then you have a very nice mechanic or more luck than I did.
Mechanic had to replace the plugs, wires (unrelated to the hydrolock but pretty shot), oil, coolant, and UIM. He told me that he had to dry out each cylinder by hand; the car must have been thirsty — the entire overflow tank and a good portion of the radiator were sucked dry.
If you get out of there and lose less than $800, then you have a very nice mechanic or more luck than I did.
#10
Retired Senior Admin
Expert Gearhead
Join Date: May 2006
Location: Sheboygan Wisconsin
Posts: 29,661
Likes: 0
Received 28 Likes
on
24 Posts
I'll put money on the fact your EGR stove pipe is cracked. Change out the UIM and you should be set. Like said earlier, look in the throttle body for coolant right at the EGR hole